Best Mooring Whips: Dolphin vs. Taylor Made vs. Dock Edge Compared

Dolphin 14ft STANDARD Mooring Whips, for boats up to 23ft. - mooring whip

Picking mooring products like mooring whips comes down to three things: how long your boat is, how much it weighs, and how your dock is set up. Get those three right and your boat stays off the dock face in wind, wake, and current without you running down to the slip every time the weather changes. Get them wrong and you are either under-powered for the load or spending more than you need to.

This guide walks through what mooring whips actually do, how Dolphin, Taylor Made, and Dock Edge products stack up, and which setup makes sense for different boats and docks. We carry Dolphin and Taylor Made mooring whips at Dock Builders Supply. Dock Edge is included here because a lot of buyers ask about them, and an honest comparison is more useful than leaving you to find it somewhere else.

Key takeaways

  • Match whip length and rated capacity to your boat's length and weight before buying anything else.
  • Dolphin mooring whips offer the best combination of price, build quality, capacity, and in stock availability for most dock owners.
  • Taylor Made whips are a solid mid-range option with good availability, but Dolphin edges them on value at nearly every size.
  • Dock Edge whips have a following, but DockBuilders.com does not carry them because Dolphin and Taylor Made consistently outperform them in capacity and durability.
  • A rocker arm base handles floating docks and tidal variation better than a fixed base.
  • Mooring whips work best alongside proper cleats, mooring lines, and snubbers sized to your boat.

What this covers:

What mooring whips do

A mooring whip is a fiberglass pole that mounts to your dock and holds a line running to your boat's bow and stern cleats. The poles flex outward, pulling the boat away from the dock face and keeping it in open water while still tethered. When waves or boat wake push your hull, the poles absorb the motion and spring the boat back to position rather than letting it grind against the dock.

That matters most on floating docks where water movement is constant, in tidal areas where the boat rises and falls a foot or more, and anywhere boat traffic is heavy. Even on a calm lake, a wake from a passing ski boat can bang a tied-up hull against a piling or a bumper hard enough to leave marks. Poles prevent that without you being there.

Mooring whips do not replace mooring lines. They work with the lines. The lines hold the boat; the poles hold it away from the dock face. You still need properly sized cleats and lines tied correctly at both ends.

Sizes, capacities, and boat types

The table below shows how pole length and rated weight capacity align with common boat sizes. These are general guidelines that apply across brands. Always check the manufacturer's rated capacity for the specific product you are buying.

Whip Length Rated Capacity Typical Boat Length Boat Types Base Style
8 ft Up to 3,500 lb Up to 20 ft Runabouts, small center consoles, jon boats, PWC Fixed base standard
12 ft Up to 5,000 lb 18 to 23 ft Pontoons, deck boats, speed boats, walkarounds Fixed or rocker arm
14 ft Up to 5,000 lb 20 to 23 ft Mid-size cruisers, express boats, sport fishers Rocker arm recommended
16 ft Up to 5,000-20,000 lb 20 to 37 ft Mid-size sportfish, flybridge cruisers, offshore boats Rocker arm required
18 ft Up to 15,000-40,000 lb 37 to 50 ft Large sportfish, flybridge cruisers, offshore boats Rocker arm required
20 ft Up to 35,000-60,000 lb 40 to 65 ft Large cabin cruisers and mid size yachts Rocker arm required
Tip When your boat falls between two capacity ratings, size up. A whip working at the edge of its rated load flexes less and wears faster. The extra cost on a longer or heavier-rated pair is small compared to replacing a set that failed or damaged your hull.

Fixed base vs. rocker arm base

A fixed base mounts the pole at a set angle. It is simpler and costs less. On a fixed dock with minimal tide and calm water, it does the job fine. The pole has a set flex range, and as long as the boat stays within that arc, everything works as intended.

A rocker arm base adds a pivot point at the mount. The base swings through a vertical arc, which lets the pole follow a floating dock as it rises and falls with tide or water level. On a floating dock in a tidal area, a fixed base can put the pole at the wrong angle as water level changes, reducing the outward pull on your boat or stressing the pole at the base. A rocker arm solves that.

If your dock floats, use a rocker arm base. If you have a tidal swing of more than 18 inches, use a rocker arm base. For a fixed dock on a lake or reservoir with stable levels, a standard fixed base is fine and saves you money.

Dolphin 16ft STANDARD Mooring Whips, for boats up to 33ft. mooring whip at Dock Builders Supply

Mooring whips vs. TideSlide: which approach suits your situation

Mooring whips and a solution like the TideSlide mooring system both solve the same problem - keeping a boat safely away from the dock face without constant re-tying. They do it in different ways, and the right choice depends on your dock type, tidal range, and how you use the boat.

The table below compares the two approaches across the factors that matter most.

Factor Mooring Whips TideSlide
How it works Fiberglass poles flex outward, lines run to bow and stern cleats Boat lines attach to a sliding car that travels up and down a dock-mounted track
Tidal range handling Rocker arm base handles up to 4-5 ft tidal swing; fixed base handles minimal tide Designed specifically for tidal variation, slides freely through the full range
Dock type Fixed or floating docks; rocker arm needed on floating Fixed pilings or dock posts; not designed for open floating dock faces
Boat size range Up to 40 ft and 10,000 lb depending on pole length Varies by piling diameter and line setup; most effective on boats up to 40 ft
Offset from dock Holds boat 2 to 4 ft off dock face depending on pole angle Boat position set by line length; adjustable at any time
Ease of boarding Board from dock edge; boat held away, so a step or gangway is useful Boat rides at dock level; boarding is natural with standard access
Installation Mount base to dock, insert pole, attach line to cleat Piling-mounted track, sliding car, and line setup; more involved
Cost range Lower entry cost; pairs start around $500-$1500 depending on size Comparable cost; a little more involved to install
Best for Open water docks, floating docks, most standard slip setups Piling-based docks with significant tidal variation

Mooring whips are the simpler, lower-cost starting point for most boat owners. TideSlide makes more sense when you are on pilings with a large tidal swing and want the boat to ride at a consistent height through the full tide cycle. For anything in between, whips handle the job with less hardware and faster installation.

Dolphin mooring whips

Dolphin has been manufacturing mooring whips in the United States for decades. Their fiberglass poles are exceptionally strong for their weight, and the brand has built a reputation for consistent quality across their full size range. Dolphin makes pairs from 8-foot standard-duty through 16-foot heavy-duty sets, covering boats from small runabouts through large offshore cruisers.

What sets Dolphin apart is build quality at a price that does not require justification. The fiberglass layup is thick, the hardware is marine grade aluminum at every connection point, and the base mounts are engineered to hold the pole at the correct angle under load. Dolphin also offers both fixed base and premium rocker arm base options across most of their size range, so you are not forced to buy more than you need for a stable dock, but you have the upgrade path available for a floating dock setup.

Dolphin's rated capacities are conservative, which is a good thing. A 5,000-pound rated pair performs at that number under real conditions. For anyone looking for the best mooring whips at a price that makes sense, Dolphin is the first place to look. Browse the full selection of Dolphin mooring whips at DockBuilders.com.

Tip Dolphin whips come with the line included in most configurations. Check what is in the box before ordering additional accessories so you are not buying rope you already have.

Dock Builders Supply Standard Duty Take-A-Part Mooring Whips for boats 17' to 20'

Taylor Made mooring whips

Taylor Made is one of the larger marine accessories brands in the country and has been proudly manufacturing dock and boat products for a long time. Their poles are a well-made option produced overseas. The fiberglass construction is solid, and Taylor Made offers multiple lengths with reliable quality throughout the range.

Taylor Made covers a similar size range to Dolphin, from smaller boats up through mid-size cruisers. Their hardware is good, the lines are properly rated, and the base mounts are straightforward to install. Where Taylor Made differs from Dolphin is primarily in price and a capped capacity around 48,000 lbs with their largest 18 ft whip. At comparable lengths and capacities, Taylor Made tends to run a bit higher, and the build differences are modest. That is not a knock on Taylor Made - they are a good product - but it does factor into the decision when both options are sitting in front of you.

Taylor Made makes sense if you have a specific product already in service and want a matching replacement, or if a particular size and configuration is what you need and Taylor Made has it in stock. See the Taylor Made options at DockBuilders.com to compare sizes and configurations side by side.

Dock Edge mooring whips

Dock Edge has long been known in the marine accessories market, and their products show up in a lot of searches because the brand has strong name recognition. Dock Edge offers economy, supreme, premium, and ultimate tiers, covering smaller boats through mid-size cruisers.

The honest assessment is that Dock Edge is not a bad product, but it lags behind Dolphin and Taylor Made in a few areas that matter. Capacity ratings in the economy and standard tiers are lower than comparable Dolphin sets at the same length. The fiberglass construction on entry-level Dock Edge poles is lighter, which shows up as reduced flex recovery over time, particularly in higher conditions. The premium and ultimate tiers are better, but at that price point, Dolphin delivers more for the dollar.

DockBuilders.com does not carry Dock Edge. That is a deliberate choice. After 25 years of selling dock hardware and talking to customers after the fact, Dolphin and Taylor Made hold up better and perform more consistently across the range of conditions a dock actually sees. If a customer calls and asks about Dock Edge, the honest answer is to point them toward a Dolphin set at the same price or slightly more, because they will not be calling back with a problem.

Knowing how to connect the mooring whips to your dock is as important as the purchase

Installation is straightforward on most docks. The base plate mounts to the dock face or the top of the decking depending on the model. Most bases use four lag screws or through-bolts. For a wood dock, 3/8-inch lag screws into solid framing work well. For aluminum or composite decking, check the base plate requirements and use the right fastener for the substrate.

Placement matters. The two poles should be spaced so one is forward of the beam and one is aft, roughly aligned with where your bow and stern lines attach. That geometry creates the outward tension that holds the boat away from the dock face. If both poles are clustered in the middle of the boat's length, you lose the spread and the boat can swing in.

The line runs from the tip of the pole down to a cleat on the boat. Keep it taut enough to hold the boat off the dock face but with enough slack that the boat can rise and fall with the tide. On a floating dock, that adjustment is minimal. On a fixed dock with tidal variation, you will re-tension as the season changes.

Pair your setup with properly sized cleats on the dock side as well. Undersized cleats are a common weak point in otherwise good docking setups. If you need to add or replace hardware, the full range of Mooring Products at DockBuilders.com covers cleats, snubbers, buoys, and everything else that goes with the setup.

Watch out Do not attach mooring whip lines to a cleat on the shore side and expect things to work correctly. The line runs from the pole tip to the boat cleat, not to the dock. Running it the wrong way loads the pole in compression rather than tension and it will not function as designed.

The bottom line: Which mooring whips should you buy?

For most boat owners on most docks, Dolphin mooring whips are the right answer. The price is fair, the quality is there, the size range covers nearly every boat from a small runabout to a large cruiser, and the hardware holds up over years of use in both freshwater and saltwater. Proudly manufacturing in the U.S. with consistent quality control, Dolphin has earned their position as the top choice in this category.

Taylor Made is worth considering if you are replacing an existing Taylor Made setup and want to stay consistent, or if a specific Dolphin configuration is out of stock and you need something now. They are a proven product and will do the job.

Dock Edge is a reasonable option if you are buying from a local retailer that only carries them, but given the choice, Dolphin or Taylor Made will serve you better over the life of the product.

Start with the right length and capacity for your boat, choose fixed or rocker arm based on your dock type, and make sure your cleats and lines are sized to match. That combination is what turns a good set of poles into a docking setup that actually works. The full range of whips and accessories is at DockBuilders.com mooring whips.

Frequently asked questions

What size mooring whips do I need for my boat?

Match whip length to your boat's overall length and check that the rated weight capacity covers your boat's loaded weight. As a general rule, boats up to 20 feet use 8-foot whips, boats from 20 to 23 feet use 14-foot whips, 23 to 33-foot boats use 16-foot whips, and larger boats from 37 to 65 feet step up to 18 or 20-foot whips. When your boat falls at the top of a capacity range, size up to the next tier.

What type of rope is used for mooring whips?

Most mooring whip sets include a braided or twisted nylon line sized for the rated capacity. Nylon is the right material because it stretches under load, which absorbs shock when waves or wake push the boat. Polypropylene floats but has poor UV resistance and low stretch, making it a poor choice for mooring lines. If you are replacing a worn line, match the diameter and length specified for your whip model.

What do mooring whips do?

Mooring whips are fiberglass poles that mount to your dock and hold lines running to your boat's bow and stern cleats. They flex outward, pulling the boat away from the dock face so it rides in open water rather than grinding against the dock. They work alongside your regular mooring lines, not instead of them, and they handle wave action and boat wake automatically without you having to re-tie.

What is the cheapest way to moor a boat?

Standard mooring lines tied to dock cleats are the lowest-cost option, but they let the boat sit against the dock, which causes hull and dock damage over time. A basic 12-foot or 14-foot mooring whip pair is the most affordable way to keep a boat properly off the dock face, and the cost is quickly offset by preventing even minor hull or dock damage. For boats on pilings in tidal water, a mooring buoy in a designated area can be a low-cost alternative to a full slip.

What size mooring whips do I need?

Size is determined by two things: your boat's length and its weight. Use boat length to pick the whip length, then confirm the rated capacity covers the actual loaded weight of your boat, including fuel, gear, and water in the tanks. If you are on a floating dock or in a tidal area with more than 18 inches of tidal swing, choose a rocker arm base model over a fixed base model.

Do mooring whips work on floating docks?

Yes, choose the type that's most compatible to your dock type, wave action or water fluctuation, and boat type. A fixed base holds the whip at a set angle, and as the floating dock rises and falls with water level or tide, that angle changes and the system works less effectively. A rocker arm base pivots at the mount, keeping the whip at the correct outward angle through the full range of dock movement.

Are Dolphin mooring whips better than Taylor Made?

Both are well-made products, but Dolphin consistently offers better value at comparable sizes. The fiberglass construction, marine grade aluminum coupler hardware, and capacity ratings hold up favorably against Taylor Made at a price that is typically lower. Taylor Made is a proven product and a solid backup option, but for a new installation where both are available, Dolphin is the first recommendation.

Hot-Dip Galvanized vs 316 Stainless Dock Hardwa...
Not All Buoys Are Built The Same